Sper-scientific 800021 RH/Temp SD Card Logger Bedienungsanleitung

RH/Temperature SD Card Datalogger 800021 Instruction Manual

- 10 - METER COMPONENTS Back of Meter Probe Battery Cover Screws Tripod Mounting Screw Stand Battery Compartment/ Cover Probe Plug Probe He

- 11 - KEYPAD LCD Display POWER (ESC, Backlight) SET (▲, TIME CHECK) LOGGER (▼, SAMPLING TIME CHECK) HOLD/ NEXT REC/ENTER

- 12 - SETUP MODE The advanced Setup Mode allows you to customize the following meter preferences and defaults: • Real Time Clock • Decimal Type

- 13 - SETUP MODE saved, the meter automatically advances to the next setup function (i.e., after setting the real time clock, the meter will au

- 14 - SETUP MODE 3. Press ▲ or ▼ to adjust the value. Press ENTER to save the value. 4. Repeat Step 3 to adjust the month, date, hour, minute a

- 15 - SETUP MODE 2. Press ▲ or ▼ to select Basic (.) or Euro (,). Press ENTER to save the selection. Auto Power Off The meter automatically tur

- 16 - SETUP MODE ENTER to save the selection. Thermometer Type K/J 1. Enter the thermometer type function from Setup Mode (see page 13). “tY

- 17 - SETUP MODE between successive measurements. To adjust the sampling time (in seconds): 1. Enter the sampling time function from Setup M

- 18 - SETUP MODE (format the SD memory card) or no (do not format the SD memory card). Press ENTER to confirm your selection. If selecting yes, “y

- 19 - MEASUREMENT PROCEDURES Turning the Unit On/Off 1. Press POWER to turn the meter on. 2. Press and hold POWER for 2 seconds to turn the

- 2 - RH/Temperature SD Card Datalogger 800021 Copyright ©2010 by Sper Scientific ALL RIGHTS RESERVED Printed in the USA 772

- 20 - MEASUREMENT PROCEDURES Note The meter will default to the last function setting used when it is turned off and on again. Humidity and Temp

- 21 - on changing the temperature scale. Dew Point 1. Follow Steps 1-2 in the preceding Humidity and Temperature section. 2. Press and hold FU

- 22 - MEASUREMENT PROCEDURES lower display. Type K/J Thermometer 1. Press POWER to turn the meter on. 2. Press and hold FUNC to cycle throug

- 23 - Hold Function 1. When measuring any parameter, press HOLD to freeze the reading on the display. “HOLD” will appear on the LCD. 2. Press HO

- 24 - 3. Press REC. The minimum value and “REC MIN” will appear on the LCD. 4. To delete the maximum or minimum value, press HOLD. “REC”

- 25 - MEASUREMENT PROCEDURES 2. Press to turn the backlight off. 3. Press to turn the backlight on. View Real Time Clock To view t

- 26 - DATALOGGER Preparing the Datalogger 1. Insert the SD card into the SD card socket on the bottom of the meter, ensuring that the front of th

- 27 - DATALOGGER 3. Press LOGGER. “REC” will flash on the LCD and the alarm will sound while the measurement data and time information are saved to

- 28 - DATALOGGER Manual Datalogging 1. Set the sampling time to 0 seconds. Refer to page 16. 2. Press REC. “REC will appear on the LCD.

- 29 - DATALOGGER 4. To finish datalogging, press REC for longer than 2 seconds. “REC” will disappear from the LCD to indicate that datalogging ha

- 3 - TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . FEATURES . . . . . . . . . . . . . . . . . . . MATERIALS SUPPLIED. . . . . . .

- 30 - DATALOGGER 4. The file’s route structure: HTA01\ HTA01001.XLS HTA01002.XLS QQQQQQQ HTA01099.XLS HTA02\ HTA02001.XLS HTA02002.XL

- 31 - BATTERY REPLACEMENT This meter uses six AA (1.5 V, UM3) batteries. When the low battery indicator appears on the LCD, batte

- 32 - TROUBLESHOOTING System Reset If the meter is not functioning properly (i.e., the system is frozen and the keypad is non-operational), re

- 33 - PC CONNECTION To save data from the SD card to a PC (using Excel software): 1. After datalogging is complete, remove the SD card from the

- 34 - PC CONNECTION channel will upload rH and temperature data; the dP channel will upload dP, rH and temperature data; the Et channel wi

- 35 - PC CONNECTION RS232 PC Serial Interface This meter has a RS232 PC serial interface via a 3.5 mm terminal. The data output is a 16 digit strea

- 36 - PC CONNECTION DO End word D1 & D8 Display reading, D1 = LSD, D8 = MSD For example: If the display reading is 1234, then D8 to

- 37 - PC CONNECTION RS232 Format: 9600, N, 8, 1 Baud rate 9600 Parity No parity Data bit no. 8 Data bits Stop bit 1 Stop bit

- 38 - OPTIONAL ACCESSORIES 800060~77 Type K Thermocouple Probes 840057 RS232 Computer Cable 840059 2GB SD Car

- 39 - SPECIFICATIONS General Circuit Custom one-chip of microprocessor LSI circuit Display LCD size: 52 mm x 38 mm Backlight function Measure

- 4 - The Sper Scientific RH/Temperature SD Card Datalogger (Model 800021) is an extremely accurate meter with fast response times that reads rel

- 40 - Operating Humidity < 85%RH Alkaline or heavy duty DC 1.5 V battery (UM3, AA) x 6 pieces DC 9V adapter input (AC/DC power adapter is optiona

- 41 - SPECIFICATIONS Humidity Temperature Dew Point (Humidity) Range 5% ~ 95% RH Resolution 0.1% RH Accuracy ≥ 70% RH: ± (3% reading + 1% R

- 42 - SPECIFICATIONS Note The dew point value is automatically calculated from the humidity/temperature measurement. The dew point accuracy is the

- 43 - SPECIFICATIONS Type K/J Thermometer Sensor Type Range Resolution Accuracy Type K -50.0 ~ 1300°C -50.1 ~ -100°C 0.1°C ± (0.4% reading + 0

- 44 - Rev. 6/17/2011 Sper Scientific warrants this product against defects in materials and workmanship for a period of five (5) years from the date

- 5 - • Functions as humidity/temperature, dew point, wet bulb, and Type K/J thermometer • SD memory card datalogger • Manual datalogger option • F

- 6 - FEATURES • Maximum and minimum • Hold function • Auto-power-off • Low battery indicator • Backlight

- 7 - MATERIALS SUPPLIED • Meter • Probe • SD Card • 6 AA Batteries • Instruction Manual • Soft Carrying Case

- 8 - POWER SUPPLY This meter can be powered by six AA (1.5 V, UM3) batteries or an optional 9 Volt DC adapter. See page 31 for battery replacement i

- 9 - Top of Meter Bottom of Meter Side of Meter METER COMPONENTS Humidity/Temperature Probe Input Socket SD Card Socket RS232 Output RESET D